AI-enabled developer productivity, build systems, and engineering leadership
Posted on in Networking
The situation: A Cisco 7604 with SAMI card is able to send packets from the individual IOS instances running on the SAMI PPCs, but is unable to receive packets.
The hardware: The table below describes the hardware involved.
| Part Number | Description |
|---|---|
| CISCO7604 | Cisco 7604 Router |
| SUP32-GE-3B | Cisco Catalyst 6500 Series … |
Posted on in Networking
This is a picture (larger) of a Cisco 7604 with Sup32 and SAMI card. The modules you see here are:
| Part Number | Description |
|---|---|
| CISCO7604 | Cisco 7604 Router |
| SUP32-GE-3B | Cisco Catalyst 6500 Series / Cisco 7600 Series Supervisor Engine 32 with 8 ports Gigabit Ethernet, PFC3B, and MSFC2A |
| WS-SVC-SAMI-BB-K9 | Cisco … |
Posted on in Networking
For some reason, they don't make this completely obvious.
login: admin
password: admin
Posted on in Networking
I would hope there is a better way to do this. The other day, I had a need to see all the interfaces on a router and how much input and output traffic they were passing. This just seems like something that should be built in, but I've not seen …
Posted on in System Administration
Configuring your syslog server to accept logging output from your Cisco routers and switches requires a few basic steps. We'll assume that you are using a new server and haven't made any previous changes to the syslog configuration. I use <acronym title="Red Hat Enterprise Linux">RHEL</acronym> 5 most …
Posted on in Networking
This seems to be a pretty common problem for Cisco users. Not that Cisco devices have more queue drop problems, just that more Cisco users are a little confused by the information generated in the show interface command.
Specifically, we're talking about the lines that look something like this:
Input …Posted on in Networking
If you find yourself in the situation where a Cisco 7200 series router has a corrupted IOS image or the flash drive has gone on the blink, the following documents may be useful to you. Not all of these documents are Cisco 7200 specific, but they are all useful.
Posted on in Networking
If you've worked on networks long enough, you're probably familiar with
iperf. This application is great for testing
throughput between two computers on your network. Unfortunately, if you find
yourself in a situation where you have less than two computers to test with,
iperf is less than ideal.
Fortunately, Cisco …
Posted on in voice
Although Cisco now markets these phones and ATAs via their Small Business line, I still think of these devices as being Linksys. Although the software that Cisco provides for these devices comes with an upgrade executable, it is only for Windows operating systems. I have found that the easiest way …
Posted on in System Administration
The default username and password for all versions of Cisco Access Registrar (as of version 5.0):
Username: admin
Password: aicuser
Perhaps this will save you a little time someday.
Posted on in Networking
In the following example, I'm going to set up a Simple Network Management Protocol version 3 (SNMPv3) user on a Cisco router with limited view of the system MIB.
Create an SNMP view that limits the user to the system MIB.
ROUTER(config)# snmp-server view SYSTEM system included
Create an …
Posted on in System Administration
If you have an interest in information security from a technical or managerial point of view, check out Principles of Information Security. It does an excellent job of presenting material for both audiences.
If you have other vendors you would like to see on this list, send me a message …
Posted on in System Administration
Previously, I mentioned that I was unable to remove the FAX= portion of the string produced by Cisco's $s$ (or $d$) macro in a T.37 store and forward fax configuration. That's still the case. I have found no way of doing this inside IOS. If it's possible, I've …
Posted on in Networking
Cisco ASA limits the number of concurrent remote-access VPN sessions a user can maintain. The default is three. When a user hits the limit, a new connection can fail or an existing idle session can be removed, depending on the configured limit and session state.
The CLI knob is still …
Posted on in Networking
There are a few network devices out there that allow you to connect, but don't give you an option to disconnect. For example, you might be stuck at a password prompt, but have no authentication details. Most telnet clients allow you to break these connections with the ^] (control-]) command. <acronym …
